![]() With these methods, you can reset both the Wi-Fi or the Ethernet network adapter on both the previous versions. In earlier versions of Windows like 7 and 8, resetting adapter was a little bit different than Windows 10. Set it accordingly and your network connection issue will be resolved.Īlso Read: 7 Best Screen Reader Apps And Software Once it restarts the network adapter will reset and may ask you to configure the network connection settings from the initial stage. Then again it will confirm that you want to reset the network settings, select Yes. After this, it will show you the message that the PC will restart in 5 minutes.ħ. It will then show you the message that it will reset all the network adapters and change all the components to their original form and the PC will restart. After that on the Network Status in the right panel, scroll down to find Network Reset and click on it.ĥ. It will open the Network Status inside this menu, if not click on the Status on the left side panel below Network & Internet.Ĥ. Now in Settings, select Network & Internet.ģ. Alternatively, you can also press Windows+I key for the same.Ģ. You can open it by clicking the Start icon and then selecting the gear icon. But before proceeding, please note that if you have any personal network settings or any kind of VPN set then you will have to enter all those settings to configure the network again after the network is reset. It is very easy to reset network adapter on your PC. 1 Reset Network Adapter Driver Settings.This could be achieved with a /etc/modprobe.d/usb-nic-sr9702. Add configuration to load the sr9700 network driver and feed it the new vendor/product ID pair, either pre-emptively at system start-up, or whenever the post-modeswitch device appears.See here for more information on configuration file parameters for usb_modeswitch. # ICS Advent/CoreChips SR9700 v2 USB ethernet NICĭepending on what exactly happens to the USB identifiers of the device when the mode-switch is triggered, you might want to add some options here to allow usb_modeswitch to verify the switching is successfully achieved. This might be achieved with a udev rule similar to what /lib/udev/rules.d/40-usb_les (or a similar file in your distro) contains, plus a configuration file named /etc/usb_modeswitch.d/0fe6:9702 with the following contents: Add configuration to trigger usb_modeswitch with the appropriate options when a "USB storage" (pre-modeswitch) device with vendor ID 0fe6 and product ID 9702 appears.If this works, then to make this configuration persistent, you would have to do two things: However, it refers to an earlier dm9601 driver you might have better luck with the sr9700 driver. This discussion suggests this approach might not work: (0FE6-9702-Kontron-ICS-Advent)= But if there are differences, the driver will most likely not work correctly. If the chips with product ID 9702 will work identically to chips with product ID 9700, this might work. If the product ID changes to 9700, you'll only need the usb_modeswitch part.īut if the product ID remains 9702 also after the modeswitch, you could try this: modprobe sr9700Įcho "0fe6 9702" > /sys/bus/usb/drivers/sr9700/new_id When the device switches to the actual network interface mode, it might or might not change its ID. The next problem could be that the sr9700 driver module will not recognize the product ID 9702, as it expects only product ID 9700. Has the class-ID: 0806 part changed to something else, perhaps to class-ID: 0206 (meaning an Ethernet network device)? Has any other information changed? Once you've done that, try the inxi -nxxx command again. This is what some mode-switching USB devices use as an indication that the Windows driver installation kit is not needed any more, and the real functionality of the device can be revealed. This tells usb_modeswitch to send a sequence of two SCSI commands to the "USB storage device": the first command is "allow media removal", the second is "eject media". ![]() Try running this command as root: usb_modeswitch -v 0fe6 -p 9702 -K This Chromium OS bug report looks very similar to your case: Or it might be the product ID used to indicate that the device is in "USB storage" mode. The USB vendor ID indicates a Kontron/ICS Advent/CoreChips product.ĬoreChips has a SR9700 network adapter chip, but the product id being 0x9702 instead of 0x9700 suggests this might be a different version of the chip.
0 Comments
Leave a Reply. |